Информатика, кибернетика и программирование

In the short period since the invention of the computer its impact on our lives has been felt in a variety of ways. From the work place to the home the computer is rapidly becoming an indispensable tool. Babbage was ahead of his time but he did envision the machine that we call a computer today.



1.08 MB

0 чел.





Department “Construction”



Checked by: Khaydarova U

                                                           Done by: Rakhmanov A



  1.  Development of the Computer
  2.  The EDSAC (Electronic Delay Storage Automatic Calculator)
  3.  The generations of the computers
  4.  Conclusion
  5.  Bibliography

Development of the Computer

          The computer is most likely one of the great technological "triggers" for future change. In the short period since the "invention" of the computer its impact on our lives has been felt in a variety of ways. From the work place to the home, the computer is rapidly becoming an indispensable tool. What is this device that is becoming so important, and how does it work? The answers lie in the history of its development, and some rather simple electronics and mathematics.

                              When humans learned to count, they probably started using their fingers as the first "digital" calculator. The abstract idea of using pebbles or sticks to represent quantities was the beginning of arithmetic and the number system we use today. Using pebbles, it is possible to add and subtract numbers quickly. If the pebbles are strung as beads on sticks or wires in a frame, it becomes an abacus , called a soroban by the Japanese. The abacus was probably invented in Western Europe and then exported to the Orient. Forgotten, or abandoned during the Dark Ages, it was reintroduced to Europe via the Arabs. In the abacus, each wire, with its beads, represents a positional number, the unit's column, the ten's column, etc. The beads can be rapidly used to add and subtract numbers. Multiplication can be handled by repetitive addition. This was the first mechanical calculator.
         The introduction of Arabic numerals into Europe in the thirteenth century was important because of its introduction of the digit zero to represent an empty position in our symbolic representation of numbers. If you don't think the zero is important, try multiplying Roman numerals! Efficient bookkeeping in commerce and government was possible, but required large numbers of clerks who had to do all the arithmetic by hand. This was not only costly, but was also fraught with error.
          While addition and subtraction are straight forward, multiplication and division require a great deal more work. These operations were made simpler by the development of the concept of logarithms by the mathematician John Napier in 1614. It is possible to multiply two numbers by adding exponents; for example, 2
2 x 2 3 = 2 2+3 = 2 5. Division can be done by subtraction of exponents. With logarithms, two numbers that are to be multiplied are first converted into powers of 10 and the exponents are then added. When 10 is raised to the power of the sum, the result is found. Compilation of logarithm tables made multiplication and division of long numbers much simpler. Later, William Oughtred invented the slide rule, a mechanical device that uses logarithms to simplify multiplication and division. The slide rule is an analog device; the values are represented on a sliding scale and do not have discrete values. By adding and subtracting distances on scales, a trained user can multiply and divide quickly.
           In 1642, Blaise Pascal developed a mechanical adding machine that used sets of wheels connected by gears. There was a wheel for each position, the one's column, the ten's and so on. By turning the wheels a number could be entered into the machine. Then by turning the wheels again, a number could be added or subtracted from the first. Carrying and borrowing were taken care of automatically by the gears. Although over fifty of these devices were made, they did not receive wide spread acceptance, especially by the clerks who feared being put out of work! Gottfried von Liebnitz, in 1674, devised a method whereby a machine could be made that would mechanically do multiplication and division. And then, in 1850, D.D. Parmalee patented a similar device that worked by pressing keys to turn the wheels and gears in the mechanical adding machine. This was the familiar "cash register". When the movement of the gears was electrified, the desk calculator was born.
           The need for accurate logarithm tables used in navigation increased with expanded commerce with the Orient during the sixteenth century. And, the introduction of the cannon in warfare required trigonometry tables. Charles Babbage convinced the English government that a machine could make possible the production of error free tables for use by the Admiralty. Babbage designed an "Analytical Engine" which would be capable of any arithmetic operation, would be instructed by punched cards (an idea borrowed from the Jacquard loom), was capable of storing numbers, comparing values, etc. Although he spent all his fortune and worked for 37 years on the project, it was never completed. The design was too complex for a purely mechanical device and the workshops of the day were simply not able to manufacture gears with the proper tolerances. Babbage was ahead of his time, but he did envision the machine that we call a computer today.
           Information stored on punched cards was used in the census of 1890 by Herman Hollerith who also borrowed the idea from the Jacquard loom. The stored information was then processed by mechanically collating, sorting, and summing the data. Hollerith was also responsible for the development of the Hollerith Code for encoding alphanumeric information as punched holes in a card. He went on to found International Business Machines (IBM).
       In 1936, Alan Turing showed that any problem can be solved by a machine if it can be expressed as a finite number of steps that can be done by the machine. Computers are therefore sometimes called Turing machines.
Howard Aiken at Harvard University built the world's first
computer in 1944. It was called the Mark I or ASCC (Automatic Sequence Controlled Calculator). The Mark I was an electromechanical machine, built to calculate cannon shell trajectories; it used relay switches. Programs and information were input by a punched paper ribbon. Aiken had managed to make the "analytic engine" that Babbage had envisioned. Unfortunately, the machine was very slow, taking seconds to multiply or divide six digit numbers. It was huge, weighed 5 tons, and contained 500 miles of wiring. The Mark I was a computer rather than a calculator because its function could be altered by changing its programming. A computer also has the ability to handle alphanumeric data as well as numbers and is capable

of storing the data. One of the giants in the development of high level languages on digital computers was Grace Murray  Hopper (1906-1992), recruited by Aiken in 1943 to be the third programmer of the Mark I. Starting in 1959 she led the design team for the COBOL language in association with Sperry Univac. Hopper was credited with coining the term "bug" in reference to a glitch in the machinery.

The first bug was actually a moth which flew through an open window and into one of the computer relays of the Mark I, temporarily shutting down the system. The moth was removed and pasted into the logbook. From then on, if Hopper's team was not producing numbers, they claimed to be "debugging the system". 1
A much faster computer than the Mark I was made possible by replacing the relays with electronic switches which rely on the movement of electrons rather than the slow physical movement of mechanical switches. The electronic switches used were vacuum tubes. John Mauchly and J. Presper Eckert at the University of Pennsylvania built the ENIAC (Electronic Numerical Integrator and Calculator) for the U.S. government to generate gunnery tables for use in the Second World War. Not finished until 1946, ENIAC contained 18,000 vacuum tubes, weighed over 30 tons, occupied 1600 square feet of floor space, and required 100 kilowatts of power. Heat dissipation was a problem and the vacuum tubes were not very reliable; when one burned out, it had to be replaced. This computer was programmed by rewiring











control boards to do the desired functions. The ENIAC was much faster than the MARK I, capable of arithmetic operations in fractions of a second. It was said at the time that this one machine would keep all the world's mathematicians busy for over 200 years!
        One difficulty that the ENIAC and MARK I had was that their design used decimal representation of numbers. John von Neumann, based on an idea by Claude Shannon, proposed that binary numbers would simplify design of computers. Since binary numbers require only two states to represent numbers, it is much easier to build the circuits, with electronic switches either on or off to represent the 1's and 0's of the binary system. Shannon also proposed the use of binary arithmetic to represent symbolic logic proposed in 1854 by George Boole. In symbolic logic, there are only two states, true and false, and several "operators" like AND and OR. Truth tables can be generated for
these operators and then be used to test logical statements. For example the truth table for the operator AND is shown above for the expression A AND B, where A and B can have the values TRUE or FALSE. The result of A AND B will only be TRUE if both A and B are TRUE. Similar truth tables can be made for the operators OR, NOT, XOR, etc. What Shannon noted was that binary arithmetic could be used in the place of the Boolean values and operators. Boole's operator AND is equivalent to binary multiplication where true is equal to 1 and false is equal to 0. In binary, 1 x 1 = 1, 1 x 0 = 0, 0 x 1 = 0, and 0 x 0 = 0. Thus, the use of binary numbers instead of decimal numbers in computers, not only simplifies design, but makes possible simple logical decision making in the design and programming of the machine.
          The EDSAC (Electronic Delay Storage Automatic Calculator) was built in England in 1949 using binary circuits and binary representation of control programs and data. This was quickly followed by the EDVAC (Electronic Discrete Variable Automatic Computer).
          Commercial applications soon followed the development of these machines. UNIVAC, an analog computer was used in the census in 1952 and attracted much attention when it was used on television to predict the election of President Eisenhower. These commercial machines were very expensive. They used vacuum tubes that were costly, required large amounts of power, gave off considerable heat, and had finite life times. Nonetheless, because of their accuracy and speed, the number of computers increased exponentially; by 1953 over 2,000 were in use.
        Then, in 1956, the transistor was invented at Bell Labs. Smaller, cheaper to manufacture, requiring less power, and more reliable, it quickly replaced the vacuum tube in computers. Thus, the
Second Generation of computers was born. With the improvements in the computer itself, improvements in peripheral devices such as card readers had to be made. Instead of punched cards, magnetic tape was introduced for the storage of information and programs. Small regions of iron on the tape could be magnetized or not to represent 1's and 0's of the binary code for numbers and information. Where one punch card could only hold 80 characters, many thousands of characters could be packed into several inches of magnetic tape.
        By 1965 the
Third Generation of computers was introduced incorporating integrated circuits. Integrated circuits are small chips of silicon wafer containing many small transistors and circuits packed into the size of a postage stamp. Smaller, cheaper, and more reliable than even the transistor, they made this generation faster, smaller, cheaper, and more powerful than ever before. The Fourth Generation of computers uses Large Scale Integration or Very Large Scale Integration of circuits. These improvements have made possible personal computers, ones cheap enough to be owned by individuals as well as companies. The Japanese are now working on the Fifth Generation of computers. They have invested the equivalent of billions of dollars in a ten year plan to design computers based upon Artificial Intelligence, ones that will recognize sound and sight and will be able to "learn" and be "taught".
           There is nothing to "see" inside a computer. Other than a tape or disk drive, there are no moving parts. A computer consists of five parts
(hardware) input and output devices, a central processing unit (CPU), the arithmetic logic unit (ALU), and a storage device.       


 Input and output devices can be card readers and punches, keyboards and video displays, printers, magnetic tapes, disks, or drums, or laser disks. Information and computer instructions or programs (software) are stored in binary format that can be read into the central processing unit. The CPU contains the control circuits for the computer and a certain amount of random access memory (RAM). These circuits are designed to move information from one memory location to another, compare values, call upon the ALU to do arithmetic, interpret program instructions, do input/output, store values, etc. All circuits are based upon high or low voltage representing the binary values 1 and 0. Storage, which can also be used for input and output, consists of tape or disk dives used to store information and programs for the computer. The arithmetic logic unit is where the arithmetic is done. Numbers are moved into registers where they can be added, subtracted, multiplied, etc.
           Although the computer is a complex design of circuits and interconnection, the basis for its operation is really quite simple. An example of this would be a simple circuit design for multiplying two binary digits (bits). If we wire two transistors in series then the output of the series connection will be the product of the two input values; unless both of the inputs are high voltage, the output will be zero.

Two transistors connected in parallel could be used for binary addition. Logic gates corresponding to the Boolean operators AND, OR, NOT, XOR, etc. can be constructed from vacuum tubes or transistors. The logic gate for AND would have three transistors wired as shown. The output (x) from such a circuit will be high voltage only when both the inputs (A & B) AND gate are high voltage. Thus, by combining thousands of such simple electronic circuits a computer can be constructed.


                Computing power is directly connected to the number of individual transistors which can fit on a microprocessor. When IBM chose the Intel 8088 microprocessor for the first IBM personal computer in 1981 there were almost 100 times as many transistors per unit area as there had been on the 4004 microprocessor just 10 years before. Gordon Moore, a founder of Intel, observed that there appeared to be an exponential growth of component density on microprocessors. His observation is now known as Moore's Law which states that microprocessor density doubles every two years (revised from the original doubling period of 1 year). The diagram at the right (copied from Chemical and Engineering News, September 13, 2004p. 26) shows the density vs. year (as a logarithmic/linear plot) for the various microprocessors used in microcomputers, starting with the 4004 in 1971.
         The development of the computer has changed the way we live and work. Communications and information retrieval are almost instantaneous. We can call an airline office anywhere in the world and get information about all available flights. Databases containing information about almost any subject is readily available to anyone with a telephone and computer. Repetitive, boring operations in manufacturing are done by computer controlled machines and robots, freeing men to do more rewarding and interesting work. Automobiles contain sophisticated computers to regulate fuel combustion and engine operation, resulting in greater gas mileage and less air pollution. Bar codes, read by computers using lasers, make inventory control automatic as well as speeding up checkout in markets. Computer Aided Design, economic forecasting, FAX machines, word processing, automatic teller machines ... the list goes on. What will the future hold? What new technologies will computers trigger? What must we wait and see?


  1.  «Automation» 2000, USA.
  2.  Reward.  Simon Sviney.  Cambridge.
  3.  Strevens, P. 1977. New orientations in the teaching of English. Oxford: Oxford University Press.
  4.  www.google.ru 
  5.  www.yahoo.com 
  6.  www.techno.Edu.ru 
  7.  www.referat.ru


А также другие работы, которые могут Вас заинтересовать

50246. Пояснить создание и настройку отчета в режиме конструктора СУБД Access 22.5 KB
  Настройка отчетов Чтобы изменить размер выделенного элемента управления можно воспользоваться маркерами изменения размера находящимися на сторонах в нижних углах и в правом верхнем углу. Для перемещения невыделенного элемента управления используйте указатель мыши. Если элемент управления имеет присоединенную надпись она перемещается вместе с ним. перемещать элемент управления и присоединенную надпись можно независимо друг от друга с помощью маркеров перемещения расположенных в левых верхних углах элемента управления и надписи.
50247. Визначення енергії дисоціації молекул йоду 896.5 KB
  Лабораторна установка для вивчення спектрів поглинання розчинів йоду зібрана на базі монохроматора УМ–2 який використовується як спектроскоп. 3 виділені оптичні елементи що входять до складу монохроматора. 2 сфокусоване конденсорною лінзою 3 світло проходить через досліджуваний розчин 4 і потрапляє на вхідну щілину 6 монохроматора. Градуювання монохроматора Для цього потрібно див.
  Классический расчет для круговой орбиты дает где eзаряд электрона;  его линейная скорость; rрадиус орбиты. Если для данного вещества экспериментально получить зависимость J=JH которая одинакова для образцов любой формы и размеров и рассчитать по формуле 2 H то на основании уравнения 1 можно найти индукцию магнитного поля в веществе. Экспериментально наиболее просто J=JH определяется для образца в виде тороида на который равномерно нанесены витки провода. 3...
  Цель работы: Определение электроемкостей отдельных конденсаторов и двух батарей из последовательно и параллельно соединенных конденсаторов. Емкость конденсатора определяется с помощью соотношения: C= где q абсолютная величина заряда на одной из обкладок конденсатора; U ...
50250. Определение электроемкости конденсатора при последовательном и параллельном соединении 164.5 KB
  Определение электроемкости конденсатора. Принципиальная схема установки или её главных узлов: Схема установки исследуемого конденсатора. Емкость конденсатора определяется с помощью соотношения:...
50251. Пристрій й основні елементи твердотельных лазерів 1.29 MB
  Устаткування й прилади Лазерна технологічна установка Квант16 ; лазер газовий ЛГ105; генераторна головка твердотільного лазера; лазерний стрижень лампа накачування відбивний блок набір дзеркал резонатора випромінювач газового лазера; штангенциркуль лінійка; матеріали вата спирт метиловий дрантя. Процес під дією якого атоми переводяться на верхні рівні називається накачуванням. Існує кілька методів накачування. У цьому випадку електромагнітна хвиля що поширюється в напрямку перпендикулярному до дзеркал буде по черзі відбиватися...
50252. Технологія одержання отвору в заготовці електроерозійної (електроіскровий) обробкою 237.5 KB
  Мета роботи: вивчити процес електроіскрової обробки технологію одержання отвору в заготовці різними способами цього виду обробки. Короткі теоретичні відомості Призначення електроерозійної обробки Цей вид обробки забезпечує великий економічний ефект при виготовленні деталей складного контуру криволінійних отворів і отворів складної форми розрізання дорогих матеріалів. Принцип електроерозійної обробки Електроерозійний спосіб обробки був відкритий в 1943 р. Один з видів електроерозійної обробки – електроіскров що характеризується імпульсами...
  ОСНОВНЫЕ ТЕОРЕТИЧЕСКИЕ ПОЛОЖЕНИЯ Вращением абсолютно твёрдого тела вокруг неподвижной оси называется такое его движение при котором все точки тела движутся в плоскостях перпендикулярных к неподвижной прямой называемой осью вращения тела и описывают окружности центры которых лежат на этой оси. Основной закон динамики вращательного движения тела закреплённого в одной неподвижной точке формулируется следующим образом: скорость изменения момента импульса тела вращающегося вокруг неподвижной точки равна...
50254. Определение длины световой волны по методу Юнга. Методическое указание 297 KB
  Совмещая перекрестие сначала с одной интерференционной полосой а затем с другой с помощью двойной риски перемещающейся по внутренней линейной шкале определяют целое число мм а по внешней круговой шкале – десятые и сотые доли мм. Отсчёты на внешней шкале барабана снимаются напротив неподвижной тонкой риски нанесённой на неподвижную часть барабана. Для этого необходимо плавно вращая барабан З установить сначала перекрестие приблизительно в центре выбранной полосы в верхней части наблюдаемого поля обычно резкое изображение...